Toyota Tundra Service Manual: Transfer Indicator Switch

Toyota Tundra Service Manual / Engine, Hybrid System / Wf1am Transfer / Transfer Indicator Switch

Components

COMPONENTS

ILLUSTRATION

Inspection

INSPECTION

PROCEDURE

1. INSPECT TRANSFER INDICATOR SWITCH

(a) Measure the resistance according to the value(s) in the table below.

Dimension (A):

24.63 to 24.89 mm (0.970 to 0.979 in.)

Dimension (B):

23.85 to 24.26 mm (0.939 to 0.955 in.)

Dimension (C):

21.89 to 22.40 mm (0.862 to 0.881 in.)

Text in Illustration

*a	Switch Condition A (4HI Position)
*b	Switch Condition B (Not 4HI / Not 4LO Position)
*c	Switch Condition C (4LO Position)
*d	Ground Position
*e	Component without harness connected (Transfer Indicator Switch)

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
1 (H4) - Case GND	Switch Condition A (4HI Position)	10 kΩ or higher
2 (L4) - Case GND	Switch Condition A (4HI Position)	10 kΩ or higher
1 (H4) - Case GND	Switch Condition B (4HI to 4LO Position)	Below 1 Ω
2 (L4) - Case GND	Switch Condition B (4HI to 4LO Position)	10 kΩ or higher
1 (H4) - Case GND	Switch Condition C (4LO Position)	Below 1 Ω
2 (L4) - Case GND	Switch Condition C (4LO Position)	Below 1 Ω

If the resistance is not as specified, replace the transfer indicator switch.

HINT:

The ground is the nut of the transfer indicator switch (connecting surface with the transfer case).

Installation

INSTALLATION

PROCEDURE

1. INSTALL TRANSFER INDICATOR SWITCH

(a) Using SST, install the transfer indicator switch.

SST: 09224-00010

Torque:

41 N·m {413 kgf·cm, 30 ft·lbf}

NOTICE:

Use the formula below to calculate special torque values for situations where SST is combined with a torque wrench (See page ).

(b) Connect the connector and attach the clamp.

2. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

for 3UR-FE: (See page )
for 1UR-FE: (See page )
for 3UR-FBE: (See page )

3. INSTALL FRONT PROPELLER SHAFT ASSEMBLY

(See page )

Removal

REMOVAL

PROCEDURE

1. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

(See page )

2. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

for 3UR-FE: (See page )
for 1UR-FE: (See page )
for 3UR-FBE: (See page )

3. REMOVE TRANSFER INDICATOR SWITCH

(a) Disconnect the connector and detach the clamp.

(b) Using SST, remove the transfer indicator switch.

SST: 09224-00010

See More:

Toyota Tundra Service Manual > Engine Immobiliser System (w/o Smart Key System): Transponder Chip Malfunction (B2793,B2794,B2797,B2798)
DESCRIPTION DTC B2793 is stored when a malfunction is found in the key during key ID code registration or a key ID code is not registered normally. Replace the key if key ID code registration cannot be performed normally and this DTC is output. DTC B2794 is stored when a key with an incomplete key I ...

Toyota Tundra Service Manual: Transfer Indicator Switch

Transfer Case Rear Oil Seal

Transfer Oil

See More:

Toyota Tundra Owners Manual

Toyota Tundra Service Manual