Toyota Tundra Service Manual: Data List / Active Test

Toyota Tundra Service Manual / Steering / Steering Column / Power Tilt And Power Telescopic Steering Column System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

(f) According to the display on the Techstream, read the Data List.

Body Electrical / Tilt & Telescopic / Data List

Tester Display

Measurement Item

Measurement Item

Normal Condition

Diagnostic Note

Tilt Position

Current tilt position data

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Position

Current telescopic position data

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Return Position

Memorized tilt return position data

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Return Position

Memorized telescopic return position data

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Memory Pos 1

Tilt data of memory position 1

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Memory Pos 1

Telescopic data of memory position 1

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Memory Pos 2

Tilt data of memory position 2

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Memory Pos 2

Telescopic data of memory position 2

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Memory Pos 3

Tilt data of memory position 3

Min.: 0

Max.: 65535

28672 to 36864

This item is not related to this vehicle

Telesco Memory Pos 3

Telescopic data of memory position 3

Min.: 0

Max.: 65535

28672 to 36864

This item is not related to this vehicle

Tilt Up Limit

Uppermost tilt position

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

Tilt Up Limit Position

Uppermost tilt position data

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Down Limit

Lowermost tilt position

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

Tilt Down Limit Position

Lowermost tilt position data

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Short Limit

Shortest telescopic position

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

Telesco Short Limit Pos

Shortest telescopic position data

Min.: 0

Max.: 65535

28672 to 36864

-

Telesco Long Limit

Longest telescopic position

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

Telesco Long Limit Pos

Longest telescopic position data

Min.: 0

Max.: 65535

28672 to 36864

-

Tilt Up Switch

Input state of tilt up switch

ON or OFF

ON: Tilt up switch activated

OFF: Tilt up switch not activated

-

Tilt Up SW(CAN)

Input state of tilt up switch

ON or OFF

-

This item is not related to this vehicle

Tilt Down Switch

Input state of tilt down switch

ON or OFF

ON: Tilt down switch activated

OFF: Tilt down switch not activated

-

Tilt Down SW(CAN)

Input state of tilt down switch

ON or OFF

-

This item is not related to this vehicle

Telesco Short Switch

Input state of telescopic contract switch

ON or OFF

ON: Telescopic contract switch activated

OFF: Telescopic contract switch not activated

-

Telesco Short SW(CAN)

Input state of telescopic contract switch

ON or OFF

-

This item is not related to this vehicle

Telesco Long Switch

Input state of telescopic extend switch

ON or OFF

ON: Telescopic extend switch activated

OFF: Telescopic extend switch not activated

-

Telesco Long SW(CAN)

Input state of telescopic extend switch

ON or OFF

-

This item is not related to this vehicle

T&T Manual SW Data

Voltage data of tilt and telescopic switch (headlight dimmer switch assembly)

Min.: 0.00 V

Max.: 4.99 V

Neutral position: Below 0.20 V

Tilt up: 1.67 to 2.13 V

Tilt down: 0.54 to 0.74 V

Telescopic contract: 1.08 to 1.40 V

Telescopic extend: 2.22 to 2.77 V

-

S/B Mem1

Tilt and telescopic memory position 1

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

S/B Mem2

Tilt and telescopic memory position 2

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

-

S/B Mem3

Tilt and telescopic memory position 3

Not Mem or Mem

Not Mem: Position not memorized

Mem: Position memorized

This item is not related to this vehicle

T&T Autoaway Function

Auto away/return function

ON or OFF

ON: Auto away/return function allowed

OFF: Auto away/return function prohibited

-

Power Source Voltage

Voltage data of power supply

Min.: 0.00 V

Max.: 19.99 V

11.00 to 14.00 V

-

Freeze Speed Info

Vehicle speed data

Min.: 0 km/h (0 mph)

Max.: 255 km/h (158 mph)

Actual vehicle speed

-

IG Switch (CAN)

Communication state of ignition switch

ON or OFF

ON: Communication normal

OFF: Communication interrupted

-

IG Switch

Input state of ignition switch

ON or OFF

ON: Input signal normal

OFF: Input signal interrupted

-

Receive from Meter

Communication state of combination meter assembly signal

OK or Interpt

OK: Communication normal

Interpt: Communication interrupted

-

Receive from Seat ECU

Communication state of front power seat switch LH signal

OK or Interpt

OK: Communication normal

Interpt: Communication interrupted

-

Receive from Combi

Communication state of combination switch ECU signal

OK or Interpt

OK: Communication normal

Interpt: Communication interrupted

This item is not related to this vehicle

J/B

Communication state of main body ECU (multiplex network body ECU) signal

OK or Interpt

OK: Communication normal

Interpt: Communication interrupted

-

Driver Information 1

Driver Information 1

Not Mem or Mem

-

-

Driver 1 Tilt Mem

Driver tilt memory position 1

Min.: 0

Max.: 65535

-

-

Driver 1 Telesco Mem

Driver telescopic memory position 1

Min.: 0

Max.: 65535

-

-

Driver Information 2

Driver Information 2

Not Mem or Mem

-

-

Driver 2 Tilt Mem

Driver tilt memory position 2

Min.: 0

Max.: 65535

-

-

Driver 2 Telesco Mem

Driver telescopic memory position 2

Min.: 0

Max.: 65535

-

-

Driver Information 3

Driver Information 3

Not Mem or Mem

-

This item is not related to this vehicle

Driver 3 Tilt Mem

Driver tilt memory position 3

Min.: 0

Max.: 65535

-

This item is not related to this vehicle

Driver 3 Telesco Mem

Driver telescopic memory position 3

Min.: 0

Max.: 65535

-

This item is not related to this vehicle

Handle Position

Steering wheel position signal

Away or Return

Away: Steering wheel in away position

Return: Steering wheel in return position

-

The Number of DTCs

Number of stored DTCs

Min.: 0

Max.: 255

Actual number of stored DTCs

-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

(f) According to the display on the Techstream, perform the Active Test.

Body Electrical / Tilt & Telescopic / Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Tilt Operation

Tilt operation

UP/DOWN

-

Telesco Operation

Telescopic operation

LONG/SHORT

-
    Customize Parameters

    Diagnosis System

    See More:

    Toyota Tundra Service Manual > Can Communication System: ECM Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area ECM Communication Stop Mode Any of the following conditions are met: Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the Techstream. Communication system DTCs (DTCs that start with U) that correspond to "EC ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0341