DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
discovered before parts or wiring is disturbed. Reading the Data List information
early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Body Electrical, Powertrain or Chassis / (desired
system) / Data List.
(e) According to the display on the Techstream, read the Data List.
Combination Meter
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
ODO/TRIP Change SW
|
Trip switch (ODO/TRIP switch) condition/ON or OFF
|
ON: Trip switch (ODO/TRIP switch) pushed
OFF: Trip switch (ODO/TRIP switch) not pushed
|
-
|
|
Vehicle Speed Meter
|
Vehicle speed/Min.: 0 (0), Max.: 255 (158)
|
Almost same as actual vehicle speed (when driving)
|
Unit: km/h (mph)
|
|
Engine Rpm
|
Engine speed/Min.: 0, Max.: 12750
|
650 to 800 rpm: Idling
|
Unit: rpm
|
|
Coolant Temperature
|
Engine coolant temperature/Min.: 0 (-40), Max.: 127.5 (261.5)
|
After warming up: 80 to 100 (176 to 212)
|
- Unit: °C (°F)
- If value -40 (-40): sensor circuit open
- If value 127.5 (261.5): sensor circuit shorted
|
|
Washer Switch
|
Washer switch/ON or OFF
|
ON: Washer switch ON
OFF: Washer switch OFF
|
-
|
|
Light Control Switch
|
Light control rheostat switch
|
Light control rheostat switch is Dark (0) → Bright (100)
|
-
|
|
+B Voltage Value
|
+B voltage/Min.: 0, Max.: 25.5
|
Below 11 to 14
|
Unit: V
|
|
Integrated value for Maintenance
|
Integrated value for maintenance warning/Min.: 0 (0), Max.: 25500 (41037)
|
0 (0) to 25500 (41037)
|
Unit: mile (km)
|
|
Ambient Temperature
|
Ambient temperature/Min.: -40 (104), Max.: 87.5 (189.5)
|
Same as outside temperature
|
Unit: °C (°F)
|
|
Fuel Level
|
Fuel sender gauge input/Min.: 0, Max.: 127.5
|
Fuel sender input value
|
Unit: L
|
|
Multi Switch (Up)
|
Steering pad switch(Up) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Multi Switch (Down)
|
Steering pad switch(Down) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Multi Switch (Enter)
|
Steering pad switch(Enter) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Multi Switch (Right)
|
Steering pad switch(Right) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Multi Switch (Left)
|
Steering pad switch(Left) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Turn Signal Switch (Right)
|
RH turn signal switch/OFF or ON
|
OFF: RH turn signal switch off
ON: RH turn signal switch on
|
-
|
|
Turn Signal Switch (Left)
|
LH turn signal switch/OFF or ON
|
OFF: LH turn signal switch off
ON: LH turn signal switch on
|
-
|
|
Hazard Flasher Switch
|
Hazard warning signal switch/OFF or ON
|
OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on
|
-
|
|
Turn Switch Signal (Full Turn)
|
Turn signal switch signal/OFF or ON
|
OFF: LH and RH turn signal switch off
ON: LH or RH turn signal switch on
|
-
|
|
Multi Switch (Back)
|
Steering pad switch (Back) /OFF or ON
|
OFF: Switch released
ON: Switch pushed
|
-
|
|
Key Remind Sound
|
Key reminder sound/FAST, NORMAL or SLOW
|
Displays key reminder buzzer speed setting
|
-
|
|
Driver Side Seatbelt Warning Buzzer
|
Front driver side seat belt warning buzzer setting/ON or OFF
|
ON: Front driver side seat belt warning buzzer ON setting
OFF: Front driver side seat belt warning buzzer OFF setting
|
-
|
|
P-Seatbelt Warning Buzzer
|
Front passenger side seat belt warning buzzer setting/ON or OFF
|
ON: Front passenger side seat belt warning buzzer ON setting
OFF: Front passenger side seat belt warning buzzer OFF setting
|
-
|
|
ODO Display Time After IG OFF Setting
|
Setting of the ODO display time after the power switch is turned off/30s,
60s, 600s, OFF
|
Displays customize setting of ODO display time after the power switch
is turned off
|
-
|
|
Lane Change Flashing Times Setting
|
Setting of the lane change flashing times/OFF, 3, 4, 5, 6, 7
|
Displays customize setting of lane change flashing times setting
|
-
|
|
TPMS System
|
Existence of function/With or Without
|
With: w/ Tire pressure warning system
Without: w/o Tire pressure warning system
|
-
|
|
LDA System
|
Existence of function/With or Without
|
With: w/ LDA system
Without: w/o LDA system
|
-
|
|
PCS System
|
Existence of function/With or Without
|
With: w/ Pre-collision system
Without: w/o Pre-collision system
|
-
|
|
Radar Cruise System
|
Radar Cruise System
|
With: w/ Dynamic radar cruise control system
Without: w/o Dynamic radar cruise control system
|
-
|
|
Number of Trouble Code
|
The number of the DTC currently stored
|
Min.: 0, Max.: 255
|
-
|
Engine
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Engine Speed
|
Engine speed/Min.: 0, Max.: 16383
|
650 to 800 rpm: Idling
|
Unit: rpm
|
|
Vehicle Speed
|
Vehicle speed/Min.: 0 (0), Max.: 255 (158)
|
Actual vehicle speed
|
- Unit: km/h (mph)
- Speed indicated on speedometer
|
|
Coolant Temp
|
Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
|
75 to 100°C (167 to 212°F): After warming up
|
If the value -40°C (-40°F): sensor circuit open.
If the value 140°C (284°F): sensor circuit shorted.
|
ABS/VSC/TRAC
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
FR Wheel Speed
|
Front wheel speed sensor RH reading
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
|
Actual wheel speed
|
Similar speed as indicated on speedometer
|
|
FL Wheel Speed
|
Front wheel speed sensor LH reading
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
|
Actual wheel speed
|
Similar speed as indicated on speedometer
|
|
RR Wheel Speed
|
Rear wheel speed sensor RH reading
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
|
Actual wheel speed
|
Similar speed as indicated on speedometer
|
|
RL Wheel Speed
|
Rear wheel speed sensor LH reading
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
|
Actual wheel speed
|
Similar speed as indicated on speedometer
|
2. ACTIVE TEST
HINT:
Using the Techstream to perform the Active Tests allows relays, VSVs and actuators
and other items to be operated without removing any parts. This non-intrusive functional
inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Tests early in troubleshooting is
one way to save diagnostic time. Data List information can be displayed while performing
Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Combination Meter
|
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
|
Speed Meter Operation
|
Speedometer
|
0, 40, 80, 120, 160, 200, 240 or 280
|
Perform the test with the vehicle stopped and the engine idling.
|
|
Acceptable range (km/h or mph): [Control range → Speedometer display]
for mph
- 40 mph → 39 to 42.5 mph
- 80 mph → 79.5 to 84 mph
for km/h
- 40 km/h → 38 to 42 km/h
- 80 km/h → 78 to 84 km/h
- 120 km/h → 119 to 125 km/h
- 160 km/h → 159 to 167 km/h
|
|
TachoMeter Operation
|
Tachometer
|
0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000
|
Perform the test with the vehicle stopped and engine idling
|
|
Fuel Meter Operation
|
Fuel receiver gauge
|
EMPTY, 1/2 or FULL
|
Perform the test with the vehicle stopped and engine idling
|
|
Water Temperature Meter Operation
|
Engine coolant temperature receiver gauge
|
OFF, LOW, NORMAL or HIGH
|
Perform the test with the vehicle stopped and engine idling
|
|
Volt Meter Operation
|
Voltmeter
|
0, 3, 6, 9, 12, 15 or 18
|
Perform the test with the vehicle stopped and engine idling
|
|
Oil Pressure Meter Operation
|
Oil pressure receiver gauge
|
OFF, LOW, 1/4, 1/2, 3/4 or HIGH
|
Perform the test with the vehicle stopped and engine idling
|
|
A/T Indicator Operation 1
|
A/T indicator (normal mode)
|
P, R, N, D, 4, 3, 2, L
|
Perform the test with the vehicle stopped and engine idling
|
|
A/T Indicator Operation 2
|
A/T indicator (sequential mode)
|
Es, 5 or 6
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Airbag
|
SRS warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Driver Side Seat Belt
|
Driver side seat belt warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp ABS
|
ABS warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Slip
|
SLIP indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Beam
|
BEAM indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Head
|
HEAD indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Fr FOG
|
Fr FOG indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Pre-Collision
|
Pre-collision warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Fuel
|
Low fuel warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
VSC TRC Indicator
|
TRAC OFF indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Tire Pressure Warning System
|
Tire pressure warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Cruise
|
CRUISE main indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Lamp Brake
|
Brake warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. EPS
|
EPS warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Master Warning
|
Master warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Auto LSD
|
AUTO LSD indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Park
|
Parking brake warning light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. Ctr DIFF LOCK
|
CENTER DIFF. indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. 4LO
|
4LO indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Indicat. VSC OFF
|
VSC OFF indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Automatic High Beam Indicator
|
Automatic high beam indicator light*5
|
OFF or ON
|
Perform the test with the vehicle stopped and engine idling
|
|
Turn Signal (Left) Indicator
|
LH turn indicator light
|
OFF or ON
|
Perform the test with the vehicle stopped and engine idling
|
|
Turn Signal (Right) Indicator
|
RH turn indicator light
|
OFF or ON
|
Perform the test with the vehicle stopped and engine idling
|
|
Check Engine Indicator
|
MIL (Check engine warning light)
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
BSM Control Indicator
|
BSM indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
TOW HAUL Indicator
|
TOW HAUL indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
RCTA Indicator
|
RCTA indicator light
|
ON or OFF
|
Perform the test with the vehicle stopped and engine idling
|
|
Multi Switch Operation
|
Multi switch
|
Top, Back, Enter, Right, Left, Down or Up
|
Perform the test with the vehicle stopped and engine idling
|
|
Meter Display 1
|
All dots in the multi-information display
|
ALL or OFF
|
Perform the test with the vehicle stopped and engine idling
|
HINT:
- If not operating normally, it can be judged that there is a malfunction
in the combination meter assembly.
- Indicator lights and warning lights which are not set do not turn on.
|
