1. DATA LIST
Using the Techstream to read the Data List allows values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
discovered before parts or wiring is disturbed. Reading the Data List information
early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
Select: Body Electrical / Sliding Roof / Data List.
(e) According to the display on tester, read the "Data List".
Sliding Roof
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Open Switch
|
Slide switch open signal/ON or OFF
|
ON: SLIDE switch is pressed to open
OFF: SLIDE switch is not pressed to open
|
-
|
|
Close Switch
|
Slide switch close signal/ON or OFF
|
ON: SLIDE switch is pressed to close
OFF: SLIDE switch is not pressed to close
|
-
|
|
Up Switch
|
Tilt switch up signal/ON or OFF
|
ON: TILT switch is pressed to up
OFF: TILT switch is not pressed to up
|
-
|
|
Down Switch
|
Tilt switch down signal/ON or OFF
|
ON: TILT switch is pressed to down
OFF: TILT switch is not pressed to down
|
-
|
|
Hall IC1 Status
|
Sliding roof operation signal/NORMAL or LOCK
|
NORMAL: Sliding roof motor is operating
LOCK: Sliding roof motor is not operating
|
-
|
|
Hall IC1 Pulse
|
Sliding roof operation signal/LO or HI
|
LO: Sliding roof motor is not operating
HI: Sliding roof motor is operating
|
-
|
|
Hall IC2 Status
|
Sliding roof operation signal/NORMAL or LOCK
|
NORMAL: Sliding roof motor is operating
LOCK: Sliding roof motor is not operating
|
-
|
|
Hall IC2 Pulse
|
Sliding roof operation signal/LO or HI
|
LO: Sliding roof motor is not operating
HI: Sliding roof motor is operating
|
-
|
|
Ignition (Direct Signal)
|
Ignition switch signal/ON or OFF
|
ON: Ignition switch ON
OFF: Ignition switch off
|
-
|
|
Ignition (MPX)
|
Ignition switch signal (MPX signal)/ON or OFF
|
ON: Ignition switch ON
OFF: Ignition switch off
|
-
|
|
Door Courtesy
|
Driver's door courtesy light switch signal/ON or OFF
|
ON: Driver's door is open
OFF: Driver's door is closed
|
-
|
|
Door Key Close Operation
|
Key-linked sliding roof open signal/ON or OFF
|
ON: Door key cylinder is turned to UNLOCK position using key
OFF: Door key cylinder is not turned to UNLOCK
|
-
|
|
Door Key Open Operation
|
Key-linked sliding roof close signal/ON or OFF
|
ON: Door key cylinder is turned to LOCK position using key
OFF: Door key cylinder is not turned to LOCK
|
-
|
|
Key Off Permission
|
Key-off sliding roof operation permit signal/ON or OFF
|
ON: Driver's side door is not closed within 45 sec after ignition switch
is turned off
OFF: Any status except "ON" status
|
-
|
|
Door Key Related (Open)
|
Key-linked sliding roof open operation status/Avail or Not Avail
|
Avail: Key-linked sliding roof open operation is available
Not Avail: Key-linked sliding roof open operation is not available
|
-
|
|
Door Key Related (Close)
|
Key-linked sliding roof close operation status/Avail or Not Avail
|
Avail: Key-linked sliding roof close operation is available
Not Avail: Key-linked sliding roof close operation is not available
|
-
|
|
Door Key Related Operation
|
Direction for key-linked operation/Tilt or Slide
|
Tilt: Key-linked sliding roof operation operates tilt up or down
Slide: Key-linked sliding roof operation operates slide open or close
|
-
|
|
Down Switch Failure (Current)
|
Down switch failure signal (Current)/ON or OFF
|
ON: Sliding roof tilt down signal failure (Current)
OFF: Sliding roof tilt down signal not fail (Current)
|
-
|
|
Up Switch Failure (Current)
|
Up switch failure signal (Current)/ON or OFF
|
ON: Sliding roof tilt up signal failure (Current)
OFF: Sliding roof tilt up signal not fail (Current)
|
-
|
|
Close Switch Failure (Current)
|
Close switch failure signal (Current)/ON or OFF
|
ON: Sliding roof close signal failure (Current)
OFF: Sliding roof close signal not fail (Current)
|
-
|
|
Open Switch Failure (Current)
|
Open switch failure signal (Current)/ON or OFF
|
ON: Sliding roof open signal failure (Current)
OFF: Sliding roof open signal not fail (Current)
|
-
|
|
Down Switch Failure (Past)
|
Down switch failure signal (Past)/ON or OFF
|
ON: Sliding roof tilt down signal failure (Past)
OFF: Sliding roof tilt down signal not fail (Past)
|
-
|
|
Up Switch Failure (Past)
|
Up switch failure signal (Past)/ON or OFF
|
ON: Sliding roof tilt up signal failure (Past)
OFF: Sliding roof tilt up signal not fail (Past)
|
-
|
|
Close Switch Failure (Past)
|
Close switch failure signal (Past)/ON or OFF
|
ON: Sliding roof close signal failure (Past)
OFF: Sliding roof close signal not fail (Past)
|
-
|
|
Open Switch Failure (Past)
|
Open switch failure signal (Past)/ON or OFF
|
ON: Sliding roof open signal failure (Past)
OFF: Sliding roof open signal not fail (Past)
|
-
|
|
Number of Trouble Codes
|
Number of trouble codes / Min.: 0, Max.: 255
|
Number of DTCs stored
|
-
|
2. ACTIVE TEST
Using the Techstream to perform Active Test allows relays, VSVs, actuators and
other items to be operated without removing any parts. This non-intrusive functional
inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Test early in troubleshooting is
one way to save diagnostic time. Data List information can be displayed while performing
Active Test.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
Select: Body Electrical / Sliding Roof / Active Test.
(e) According to the display on tester, perform the "Active Test".
Sliding Roof
