DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
discovered before parts or wiring is disturbed. Reading the Data List information
early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Body Electrical / (desired system) / Data List.
(g) According to the display on the Techstream, read the Data List.
Master Switch
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
D Door P/W Auto SW
|
Driver side power window auto UP/DOWN switch signal / ON or OFF
|
ON: Driver side switch of master switch operated
OFF: Driver side switch of master switch not operated
|
-
|
|
P Door P/W Auto SW
|
Front passenger side power window remote auto UP/DOWN switch signal /
ON or OFF
|
ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
|
-
|
|
P Door P/W Up SW
|
Front passenger side power window remote manual UP switch signal / ON
or OFF
|
ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
|
-
|
|
P Door P/W Down SW
|
Front passenger side power window remote manual DOWN switch signal /
ON or OFF
|
ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
|
-
|
|
Window Lock Switch Status
|
Power window LOCK switch / ON or OFF
|
ON: Power window lock switch in LOCK position
OFF: Power window lock switch in UNLOCK position
|
-
|
|
Number of Trouble Codes
|
Number of trouble codes / Min.: 0, Max.: 255
|
Number of DTCs will be displayed
|
-
|
D-Door Motor
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
D Door P/W Auto SW
|
Driver side power window auto UP/DOWN switch signal / ON or OFF
|
ON: Driver side switch operated
OFF: Driver side switch not operated
|
-
|
|
D Door P/W Up SW
|
Driver side power window MANUAL UP switch signal / ON or OFF
|
ON: Driver side switch operated
OFF: Driver side switch not operated
|
-
|
|
D Door P/W Down SW
|
Driver side power window MANUAL DOWN switch signal / ON or OFF
|
ON: Driver side switch operated
OFF: Driver side switch not operated
|
-
|
|
Number of Trouble Codes
|
Number of trouble codes / Min.: 0, Max.: 255
|
Number of DTCs will be displayed
|
-
|
P-Door Motor
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
P Door P/W Auto SW
|
Front passenger side power window auto UP/DOWN switch signal / ON or
OFF
|
ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
|
-
|
|
P Door P/W Up SW
|
Front passenger side power window manual UP switch signal / ON or OFF
|
ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
|
-
|
|
P Door P/W Down SW
|
Front passenger side power window manual DOWN switch signal / ON or OFF
|
ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
|
-
|
|
Number of Trouble Codes
|
Number of trouble codes / Min.: 0, Max.: 255
|
Number of DTCs will be displayed
|
-
|
Main Body
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
D Door Courtesy SW
|
Driver side door courtesy switch signal / ON or OFF
|
ON: Driver door open
OFF: Driver door closed
|
-
|
|
P Door Courtesy SW
|
Front passenger side door courtesy switch signal / ON or OFF
|
ON: Front passenger door open
OFF: Front passenger door closed
|
-
|
|
Door Lock SW-Lock
|
Driver side door lock switch signal / ON or OFF
|
ON: Door control switch is pushed to lock position
OFF: Door control switch is not pushed
|
-
|
|
Door Lock SW-Unlock
|
Driver side door unlock switch signal / ON or OFF
|
ON: Door control switch is pushed to unlock position
OFF: Door control switch is not pushed
|
-
|
|
Door Key P/W Up
|
Function to close the driver side door window while holding the key to
the lock side for more than about 2.3 seconds / ON or OFF
|
Customize setting displayed
|
-
|
|
Door Key P/W Down
|
Function to open the driver side door window while holding the key to
the unlock side for more than about 2.3 seconds / ON or OFF
|
Customize setting displayed
|
-
|
|
Communication D-Door Motor
|
Connection status between power window regulator motor (for driver side)
and main body ECU / OK or Stop
|
OK: Connection
Stop: No connection
|
-
|
|
Communication P-Door Motor
|
Connection status between power window regulator motor (for front passenger
side) and main body ECU / OK or Stop
|
OK: Connection
Stop: No connection
|
-
|
|
Communication Master SW
|
Connection status between master switch and main body ECU / OK or Stop
|
OK: Connection
Stop: No connection
|
-
|
|
Door Key SW-Lock
|
Door key linked lock switch signal / ON or OFF
|
ON: Driver side door key cylinder is turned to lock position
OFF: Driver side door key cylinder is not turned
|
-
|
|
Door Key SW-Unlock
|
Door key linked unlock switch signal / ON or OFF
|
ON: Driver side door key cylinder is turned to unlock position
OFF: Driver side door key cylinder is not turned
|
-
|
2. PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and
other items to be operated without removing any parts. This non-intrusive functional
inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Tests early in troubleshooting is
one way to save diagnostic time. Data List information can be displayed while performing
Active Tests.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Body Electrical / (desired system) / Active Test.
(g) According to the display on the Techstream, perform the Active Test.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During
the Active Test, the jam protection function does not operate.
D-Door Motor
|
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
|
Power Window
|
Driver side power window
|
OFF/UP/DOWN
|
-
|
P-Door Motor
|
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
|
Power Window
|
Front passenger side power window
|
OFF/UP/DOWN
|
-
|
Main Body
|
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
|
IG OFF P/W Control Permission Output
|
Power window control permission output
|
ON or OFF
|
-
|
| 
