|
Tester Display | Measurement Item/Range |
Normal Condition | Diagnostic Note |
|
Warning Indicator Turning on(Slave) |
State of the outer rear view mirror indicator LH turning on / OFF or ON |
OFF: Any state except "ON"
- ON: Either of the following states
- During initial check
- Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch not on
| - |
|
Warning Indicator Flashing(Slave) | State of the outer rear view mirror indicator LH turning on / OFF or ON |
OFF: Any state except "ON"
- ON: Either of the following state
- Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on
- Vehicle detected by RCTA function
| - |
|
Buzzer Sound Status | State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON |
OFF: Buzzer not sounding ON: Buzzer sounding |
- |
| Warning Indicator Input Circuit Voltage |
Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V |
Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V |
- |
| Warning Indicator Input Circuit Current |
Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA |
Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA |
- |
| Buzzer Input Circuit Voltage |
RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V |
Buzzer not sounding: 11 to 14 V Buzzer sounding: Alternating between 0 to 14 V |
- |
| Turn Switch State |
State of the turn signal switch / Left ON, Right ON or OFF |
Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on
OFF: Turn signal light switch off |
- |
| Reverse (Only for AT/CVT) |
State of the shift position R signal / OFF or ON |
OFF: Shift lever in any position except R ON: Shift lever in R |
- |
| Vehicle Speed |
Vehicle speed signal / Min.: 0 km/ h (0 mph), Max.: 326 km/h (203 mph) |
Almost same as actual vehicle speed |
- |
| Steering Angle |
Steering angle sensor / Min.: - 3072°, Max.: 3070.5° |
Left turn: Increases Right turn: Decreases |
- |
| Power Supply Voltage |
Power supply voltage / Min.: 0 V, Max.: 49.951 V |
Ignition switch ON: 11 to 14 V |
- |
| Indicator Light Control State |
Outer rear view mirror indicator dimming state / Dim OFF or Dim ON |
Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
| HV Flag |
Hybrid vehicle / OFF or ON | OFF: Non-hybrid vehicle
ON: Hybrid vehicle | It does not change from OFF |
|
VGRS Flag | VGRS installed / OFF or ON |
OFF: VGRS not installed ON: VGRS installed |
- |
| Beam Axis Inspection Completeness Flag |
Completion of beam axis inspection / Incompl or Compl |
Incompl: Inspection not completed Compl: Inspection completed |
Changes to Compl when Test Mode has been entered. |
|
Destination Undefined Flag |
Destination determination / Unfixed or Fixed |
Unfixed: Sensor destination information not determined Fixed: Sensor destination information determined according to CAN destination information |
- |
| Angle Adjustment by Auto Alignment |
Angle adjusted using auto alignment / Min.: Under -180 deg, Max.: Over 180 deg |
Angle adjusted using auto alignment is displayed |
- |
| RCTA Equipped Information |
Status of the RCTA equipped information / ON or OFF |
OFF: RCTA function off ON: RCTA function on |
- |
| Slave Side RCTA Function |
Switches the RCTA function on and off / OFF or ON |
OFF: RCTA function off ON: RCTA function on |
- |
| Mirror LED Control Frequency |
Frequency of the outer rear view mirror indicator on the outer mirror when blinking / Min.: 1500 Hz, Max.: 2400 Hz |
Always: 2000 Hz | - |
|
Setting of Warning Indicator Current (Dim OFF) |
Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA |
Bright: 75 mA Dark: 60 mA |
- |
| Setting of Warning Indicator Current (Dim ON) |
Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA |
Bright: 60 mA Dark: 30 mA |
- |
| Mirror LED Duty Ratio (Blinking) |
Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% |
Always: 50 % | - |
|
Buzzer Control Frequency |
Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz |
Always: 2000 Hz | - |
|
Yaw Rate Sensor | Yaw rate sensor / Min.: Under -124.928 deg/s, Max.: 124.684 deg/s |
Turning right: -124.928 to 0 deg/s Turning left: 0 to 124.684 deg/s |
- |
| BSM Buzzer Volume Adjust |
Status of the RCTA buzzer (blind spot monitor buzzer) volume adjust / Low, Medium or High |
Low: Buzzer volume less than that of medium Medium: Default buzzer volume
High: Buzzer volume more than that of medium |
- |
| Mounting FHL Function |
Existence of FHL function / Without or With |
Without: w/o FHL function With: w/ FHL function |
- |
| Number of DTC |
Number of DTCs / Min.: 0, Max.: 255 |
When system normal: 0 When malfunction detected: More than 0 |
- |
