|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|
ABS Warning Light | ABS warning light |
ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Brake Warning Light |
Brake warning light | ON or OFF |
ON: Warning light on OFF: Warning light off |
- |
| Stop Light SW |
Stop light switch assembly |
ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Parking Brake SW |
Parking brake switch assembly |
ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
| Main Idle SW |
Main idle switch | ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
| Brake Pedal Load Sensing SW |
Brake Pedal Load Sensing Switch |
ON or OFF | ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point |
- |
| Gear Position |
Gear position information |
"P, N", R, 1st-10th, Fail or Not R |
Actual gear position |
- |
| Shift Lever Position |
Shift lever position information |
"P, N", R, D/M, 1st-6th/B or Fail |
Actual shift lever position |
- |
| Shift Information |
Shift information | ON or OFF |
ON: During gear change OFF: Not during gear change |
- |
| Inspection Mode |
Inspection mode | Other or Inspect |
Other: Normal mode Inspect: Inspection mode |
- |
| Number of IG ON(Inspection) |
Number of times ignition switch turned to ON after entering inspection mode |
Min.: 0, Max.: 255 | - |
- |
| Master Cylinder Sensor |
Master cylinder pressure sensor reading |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.20 to 0.40 V |
Reading increases when brake pedal is depressed |
|
Deceleration Sensor | Lateral acceleration sensor (GL1) reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Deceleration Sensor2 | Longitudinal acceleration sensor (GL2) reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele2 | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Yaw Rate Sensor | Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate |
Memorized zero value | Min.: -128°, Max.: 127° |
- | After completing zero point calibration: 0° |
|
Steering Angle Sensor | Steering angle sensor |
Min.: -3276.8°, Max.: 3276.7° |
Turning left: Increases Turning right: Decreases |
- |
| Zero Point of Steering Angle |
Memorized zero value | Min.: -3276.8°, Max.: 3276.7° |
- | After steering angle sensor zero point calibration: 0° |
|
Lateral G | Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and rearward G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
|
Yaw Rate Value | Yaw rate value |
Min.: -128°/s, Max.: 127°/s |
- | During turning: Changes in proportion with yaw |
|
Steering Angle Value | Steering angle value |
Min.: -3276.8°, Max.: 3276.7° |
- | During steering operation: Changes in proportion with steering wheel rotation |
|
Stop Light Relay | Stop light control relay (VSC ACC)
(STP2 terminal input) | ON or OFF |
ON: Relay input on OFF: Relay input off |
- |
| Slip Indicator Light |
Slip indicator light | ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
| FR Wheel Speed |
Front wheel speed sensor RH reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FL Wheel Speed | Front wheel speed sensor LH reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RR Wheel Speed | Rear wheel speed sensor RH reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RL Wheel Speed | Rear wheel speed sensor LH reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
Vehicle Speed | Maximum wheel speed sensor reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FR Wheel Acceleration | Front wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
| FL Wheel Acceleration |
Front wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
| RR Wheel Acceleration |
Rear wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
| RL Wheel Acceleration |
Rear wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
- Displays a negative value during deceleration and a positive value during acceleration
- During deceleration/acceleration: Changes continuously
|
| Stop Light Relay Output |
Stop light control relay (VSC ACC) (STPO terminal output) |
ON or OFF | ON: Relay output on
OFF: Relay output off |
- |
| FR Wheel ABS Ctrl Status |
Front wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| FL Wheel ABS Ctrl Status |
Front wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| RR Wheel ABS Ctrl Status |
Rear wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| RL Wheel ABS Ctrl Status |
Rear wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| FR Wheel EBD Ctrl Status |
Front wheel RH EBD control status |
ON or OFF | ON: During control |
- |
| FL Wheel EBD Ctrl Status |
Front wheel LH EBD control status |
ON or OFF | ON: During control |
- |
| RR Wheel EBD Ctrl Status |
Rear wheel RH EBD control status |
ON or OFF | ON: During control |
- |
| RL Wheel EBD Ctrl Status |
Rear wheel LH EBD control status |
ON or OFF | ON: During control |
- |
| BA Ctrl Status |
BA control status | ON or OFF |
ON: During control | - |
|
PBA Ctrl Status | PBA control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Ctrl Status |
TRAC control status | ON or OFF |
ON: During control | - |
|
TRC(TRAC) Engine Ctrl Status |
TRAC engine control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Brake Ctrl Status |
TRAC brake control status |
ON or OFF | ON: During control |
- |
| FR Wheel VSC Ctrl Status |
Front wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| FL Wheel VSC Ctrl Status |
Front wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| RR Wheel VSC Ctrl Status |
Rear wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| RL Wheel VSC Ctrl Status |
Rear wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| Engine Revolutions |
Engine speed | Min.: 0 rpm, Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
|
Real Engine Torque | Real engine torque |
Min.: -1024 Nm, Max.: 1023 Nm |
- | - |
|
Accelerator Opening Angle % |
Percentage of accelerator pedal opening angle |
Min.: 0.0%, Max.: 127.5% |
Accelerator pedal released: 0.0% |
During accelerator pedal operation: Changes in proportion with the pedal movement |
|
Solenoid Relay | ABS solenoid relay |
ON or OFF | ON: ABS solenoid relay on
OFF: ABS solenoid relay off |
- |
| ECB Motor Relay |
ABS motor relay | ON or OFF |
ON: ABS motor relay on OFF: ABS motor relay off |
- Not applicable to this vehicle
- ECB: Electronically Controlled Brake
|
| TR(A)C/VSC Solenoid (SRM2) |
Master cut solenoid (SRM2) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRM1) |
Master cut solenoid (SRM1) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRC2) |
Master cut solenoid (SRC2) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRC1) |
Master cut solenoid (SRC1) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SFRH) |
ABS solenoid (SFRH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SFRR) | ABS solenoid (SFRR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SFLH) |
ABS solenoid (SFLH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SFLR) | ABS solenoid (SFLR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SRRH) |
ABS solenoid (SRRH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SRRR) | ABS solenoid (SRRR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SRLH) |
ABS solenoid (SRLH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SRLR) | ABS solenoid (SRLR) |
ON or OFF | ON: During control |
- |
| EFI Communication Open |
ECM communication open detection |
Error or Normal | Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
|
Yaw Rate Open | Yaw rate sensor open detection |
Error or Normal | Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
|
Deceleration Open | Acceleration sensor open detection |
Error or Normal | Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
|
Steering Open | Steering angle sensor open detection |
Error or Normal | Error: Momentary interruption detected
Normal: Momentary interruption not detected |
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal". |
|
BS1 Voltage Value | +BS voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to battery voltage |
|
MT Voltage Value | Motor voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to battery voltage |
|
TRAC/VSC Off Mode | TRAC/VSC off mode |
Normal, TRC OFF or VSC OFF |
Normal: Normal mode TRC OFF: TRAC off mode VSC OFF: VSC off mode |
- |
| Number of DTC |
Number of DTC recorded |
Min.: 0, Max.: 255 | - |
- |
| IG Voltage Value Decreased |
+BS voltage value decrease detection |
Error or Normal | Error: Low voltage detected
Normal: Low voltage not detected |
- After low voltage occurs, if there is no low voltage error for 1 second, it switches from "Error" to "Normal".
- Error: 9.8 V or less
|
| IG Voltage Value Increased |
+BS voltage value increase detection |
Error or Normal | Error: High voltage detected
Normal: High voltage not detected |
- After high voltage occurs, if there is no high voltage error for 1 second, it switches from "Error" to "Normal".
- Error: 17.4 V or higher
|
