Toyota Tundra Service Manual: Internal Control Module Throttle Position Performance (P060E)

Toyota Tundra Service Manual / Engine, Hybrid System / 1ur-fe Engine Control / Sfi System / Internal Control Module Throttle Position Performance (P060E)

DESCRIPTION

The ECM monitors the input signals of the Throttle Position (TP) sensor No. 1 and stop light switch. As the ECM monitors the input signals of the TP sensor No. 1 and the STP signals of the stop light switch, if the input signals and control signals deviate, a DTC is output.

DTC No.

DTC Detection Condition

Trouble Area

P060E

When either condition below is met:

  • ECM main CPU error
  • ECM sub CPU error

(1 trip detection logic)

ECM

MONITOR STRATEGY

Related DTCs

P060E: Internal Control Module, Throttle Position

Required sensors/Components (Main)

ECM

Required sensors/Components (Related)

-

Frequency of operation

Continuous

Duration

1 second: Case 1

13 times: Case 2

MIL operation

Immediate

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

Case 1

Monitor runs whenever following DTCs not present

None

Case 2

Monitor runs whenever following DTCs not present

None

DMA communication error

Not detected

TYPICAL MALFUNCTION THRESHOLDS

Case 1

Difference of main TP and sub TP

0.3 V or more

Case 2

Difference of main brake switch signal and sub brake switch signal

Different

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 16 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P060E.
  11. Check the DTC judgment result.

    Tester Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).

    HINT:

    • If a permanent DTC is output, the system is malfunctioning.
    • If no permanent DTC is output, the system is normal.

CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page ).

HINT:

Read freeze frame data using a Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK FOR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear DTCs (See page ).

(e) Turn the ignition switch off and turn the Techstream off.

(f) Disconnect the Techstream.

(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(h) Connect the cable to the negative (-) battery terminal.

(i) Connect the Techstream to the DLC3.

(j) Turn the ignition switch to ON.

(k) Turn the Techstream on.

(l) Wait for 16 seconds or more.

(m) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

(n) Read DTCs.

OK:

P060E is not present.

OK

CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE ECM

    Internal Control Module Accelerator Pedal Position Performance (P060D)

    Internal Control Module EEPROM Error (P062F)

    See More:

    Toyota Tundra Service Manual > Air Conditioning: Air Conditioning Panel
    Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (a) Attach the 3 clips to install the air conditioning control assembly to the center lower instrument panel finish panel. Text in Illustration *1 Air Conditioning Control Assembly *2 ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0119